Production Operation and Problem Solving
LATAR BELAKANG
Setelah menyelesaikan training ini peserta diharap mampu:
- Memahami prinsip-prinsip dasar perhitungan dan melakukan optimisasi pada saat operasi produksi sumur-sumur minyak, gas dan reservoir panas bumi dilaksanakan, pengembangan pelaksanaan optimisasi produksi ini untuk meningkatkan kinerja produksi sumuran dan lapangan.
- Melakukan diagnosis sederhana dan mengerti penyelesaian permasalahan dalam operasi produksi sumur-sumur minyak dan gas bumi.
- Membuat analisis sederhana terhadap data sumuran minyak, gas dan panas bumi, melakukan peramalan kinerja dan merencanakan pengembangan operasi produksi.
- Melakukan perhitungan-perhitungan kuantitatif sederhana dari seluruh data perolehan data tubing, flowline, choke, perforasi, gravel pack, subsurface safety valve pada sumuran, merancanakan pengembangannya dengan memperhitungkan kemampuan masing-masing sumuran.
- Mempergunakan pengetahuan operasi produksi untuk keperluan penyelesaian permasalahan sumur seperti; pada saat penyemenan, penanganan scale, pasir, korosi dan damage yang mungkin terjadi pada sumuran minyak dan gas bumi.
- Memahami prinsip-prinsip dasar perancangan; penyemenan, workover, stimulasi sumuran dengan pengasaman dan perekahan hidrolik, perencanaan workover dll.
PRE-REQUISITE
Latar belakang: Operator, Senior Operator, Engineer, Non-Engineer
MATERI
Geologic Considerations in Producing Operation
- Introduction
- Sandstone reservoirs
- Geologic factors affecting reservoir properties in sandstone
- Application of geologic concepts in specific sandstone
- Carbonate reservoirs
- Application of geologic concepts in carbonate reservoir
Reservoir Considerations in Well Completions
- Introduction
- Hydrocarbon properties of oil and gas
- Recommendations of obtaining good test data
- Eyeball interpretation of pressure charts
Primary Cementing
- Introduction
- Cementing materials
- Cement additives
- Cement bonding
- Flow properties of primary cement
- Displacement mechanics
- Cost of primary cementing
- Special problem situations-new developments
- Primary cementing practices
Well Completion Design
- Factors influencing well completion design
- Conventional tubular configurations
- Unconventional tubular configurations
- Sizing production tubular
- Completion interval
- Permanent well completions (PWC)
- Tubingless completion
Tubing String, Packers, Subsurface Control Equipment
- Tubing string
- Steel grades
- Tubing connections
- Makeup of API threaded connection
- Design of tubing string
- High strength tubing
- Physical properties of steel
- Sensitivities of high strength tubing
- Tubing inspection
- Tubing handling practices
- Equipment for use with-strength tubing
- Tubing running practices
- API publication list
- Packers and subsurface control equipment
- Production packers
- Subsurface control equipment
Perforating Oil and Gas Well
- Introduction
- Types of perforators
- Evaluation of perforator performance
- Factors affecting gun perforating result
- Perforating in a clean fluid with differential pressure into wellbore
- A comparison between the GEO-VANN system and other perforating methods in wells equipped with packers
Completion and Workover Fluids
- Function-requirements-selection criteria
- Formation damage related to solids
- Oil fluids-practical application
- Conventional water-base mud
- Oil base or invert-emulsion muds
- Foam
- Perforating fluids
- Packer fluids
- Well killing
Through-Tubing Production Logging
- Introduction
- Logging device
- Application of through-tubing production logging
- Field examples of production logging techniques
- Primary cement evaluation
Problem Well Analysis
- Problem wells
- Problem well analysis checklist
Paraffin and Asphaltene
- Introduction
- Paraffin and asphaltene chemistry
- Deposition mechanism
- Removal of wax depositsPreventing or decreasing wax deposition
- Design of wax control
Squeeze Cementing-Remedial Cementing
- Introduction
- Theoretical considerations
- Practical considerations
- Special squeeze cementing situations
- Planning a squeeze cement job
- Normal operational procedures
- Other operational procedures
- Plug-back operations
- Special cement system
Sand Control
- Introduction
- Reduction of drag force
- Mechanical methods of sand control
- Practical considerations in gravel packing
- Use of screen without gravel
- Resin consolidation methods
Formation Damage
- Introduction
- Basic causes of damage
- Classification of damage mechanism
- Reduced absolute permeability
- Increased fluid viscosity (emulsion)
- Diagnosis of formation damage
surfactants for Well Treatments
- Characteristics of surfactants
- Use and action of surfactants
- Formation damage susceptible to surfactant treatment
- Preventing or removing damage
- Increasing effectiveness of rod pumping
- Prevention of well damage
Acidizing
- Acids used in well stimulation
- Acid additives
- Carbonate acidizing
- Acidizing techniques for carbonate formations
- Sandstone acidizing
- Potential safety hazard in acidizing
Hydraulic Fracturing
- Introduction
- Mechanics of fracturing
- Production increase from fracturing
- Propping the fracture
- Frac fluids
- Frac job design
- Frac job evaluation techniques
Scale Deposition, Removal and Prevention
- Introduction
- Causes of scale deposition
- Prediction and identification of scale
- Scale removal
- Scale prevention
Corrosion Control
- The corrosion process
- Detection and measurement of corrosion
- Corrosion control
INSTRUKTUR
Team Konsultan PT Ganesha Inti Persada
WAKTU PELAKSANAAN
3 Hari (dimulai pukul: 09.00-16.00)
INVESTASI (Tidak termasuk biaya akomodasi & penginapan)
- Rp. 11.000.000, - / peserta (Jakarta)
- Rp. 11.000.000, - / peserta (Bandung)
- Rp. 12.000.000, - / peserta (Yogyakarta)
- Rp. 14.000.000, - / peserta (Bali)
- Rp. 14.750.000, - / peserta (Lombok, Batam, Makasar)
- US$ 4780 / peserta (Malaysia)
FASILITAS
Lunch, sertifikat, Modul, Coffee Break, Training kit diselenggarakan di Hotel berbintang
INFO & PROMO
081296791324 (WA)
021-22830080
CONTACT PERSON
0811-996-1224 (WA)
0812-9679-1224 (WA)
JADWAL TRAINING TAHUN 2024 :
November
- 20-22 November 2024, Surabaya
- 27-29 November 2024, Yogyakarta
Desember
- 4-6 Desember 2024, Bandung
- 11-13 Desember 2024, Medan/ Jakarta
- 18-20 Desember 2024, Makassar/ Yogyakarta
Jadwal Online & OfflineTahun 2025:
Januari
- 6-8 Januari 2025, Jakarta
- 8-10 Januari 2025, Bandung
- 13-15 Januari 2025, Yogyakarta
- 22-24 Januari 2025, Bali
Februari
- 3-5 Januari 2025, Yogyakarta
- 10-12 Januari 2025, Bandung
- 17-19 Januari 2025, Batam
- 24-26 Januari 2025, Jakarta
Maret
- 3-5 Maret 2025, Malang
- 10-12 Maret 2025, Bandung
- 17-19 Maret 2025, Jakarta
- 24-26 Maret 2025, Yogyakarta
April
- 9-11 April 2025, Bandung
- 14-16 April 2025, Jakarta
- 23-25 April 2025, Yogyakarta
- 28-30 April 2025, Surabaya
Mei
- 5-7 Mei 2025, Jakarta
- 13-15 Mei 2025, Yogyakarta
- 21-23 Mei 2025, Lombok
- 26-28 Mei 2025, Malang
Juni
- 4-6 Juni 2025, Jakarta
- 11-13 Juni 2025, Yogyakarta
- 18-20 Juni 2025, Bandung
- 24-26 Juni 2025, Bali
Juli
- 2-4 Juli 2025, Bandung
- 9-11 Juli 2025, Jakarta
- 16-18 Juli 2025, Lombok
- 23-25 Juli 2025, Yogyakarta
- 29-31 Juli 2025, Medan
Agustus
- 6-8 Agustus 2025, Bandung
- 13-15 Agustus 2025, Jakarta
- 20-22 Agustus 2025, Malang
- 27-29 Agustus 2025, Bali
September
- 1-3 September 2025, Bandung
- 10-12 September 2025, Surabaya
- 17-19 September 2025, Jakarta
- 22-24 September 2025, Lombok
Oktober
- 1-3 Oktober 2025, Yogyakarta
- 8-10 Oktober 2025, Jakarta
- 15-17 Oktober 2025, Bandung
- 22-24 Oktober 2025, Bali
November
- 3-5 November 2025, Lombok
- 10-12 November 2025, Jakarta
- 17-19 November 2025, Bandung
- 24-26 November 2025, Malang
Desember
- 3-5 Desember 2025, Jakarta
- 10-12 Desember 2025, Bandung
- 17-19 Desember 2025, Surabaya
- 22-24 Desember 2025, Yogyakarta
Klik link form registrasi https://bit.ly/FormRegistrasiPTGIP
Kami menerima request waktu, tempat & fasilitas hubungi kami untuk informasi lebih lanjut.
