Production Operation and Problem Solving

LATAR BELAKANG

Setelah menyelesaikan training ini peserta diharap mampu:

1. Memahami prinsip-prinsip dasar perhitungan dan melakukan optimisasi pada saat operasi produksi sumur-sumur minyak, gas dan reservoir panas bumi dilaksanakan, pengembangan pelaksanaan optimisasi produksi ini untuk meningkatkan kinerja produksi sumuran dan lapangan.
2. Melakukan diagnosis sederhana dan mengerti penyelesaian permasalahan dalam operasi produksi sumur-sumur minyak dan gas bumi.
3. Membuat analisis sederhana terhadap data sumuran minyak, gas dan panas bumi, melakukan peramalan kinerja dan merencanakan pengembangan operasi produksi.
4. Melakukan perhitungan-perhitungan kuantitatif sederhana dari seluruh data perolehan data tubing, flowline, choke, perforasi, gravel pack, subsurface safety valve pada sumuran, merancanakan pengembangannya dengan memperhitungkan kemampuan masing-masing sumuran.
5. Mempergunakan pengetahuan operasi produksi untuk keperluan penyelesaian permasalahan sumur seperti; pada saat penyemenan, penanganan scale, pasir, korosi dan damage yang mungkin terjadi pada sumuran minyak dan gas bumi.
6. Memahami prinsip-prinsip dasar perancangan; penyemenan, workover, stimulasi sumuran dengan pengasaman dan perekahan hidrolik, perencanaan workover dll.

PRE-REQUISITE

Latar belakang: Operator, Senior Operator, Engineer, Non-Engineer

MATERI

Geologic Considerations in Producing Operation

• Introduction
• Sandstone reservoirs
• Geologic factors affecting reservoir properties in sandstone
• Application of geologic concepts in specific sandstone
• Carbonate reservoirs
• Application of geologic concepts in carbonate reservoir

Reservoir Considerations in Well Completions

• Introduction
• Hydrocarbon properties of oil and gas
• Recommendations of obtaining good test data
• Eyeball interpretation of pressure charts

Primary Cementing

• Introduction
• Cementing materials
• Cement additives
• Cement bonding
• Flow properties of primary cement
• Displacement mechanics
• Cost of primary cementing
• Special problem situations-new developments
• Primary cementing practices

Well Completion Design

• Factors influencing well completion design
• Conventional tubular configurations
• Unconventional tubular configurations
• Sizing production tubular
• Completion interval
• Permanent well completions (PWC)
• Tubingless completion

Tubing String, Packers, Subsurface Control Equipment

• Tubing string
• Steel grades
• Tubing connections
• Makeup of API threaded connection
• Design of tubing string
• High strength tubing
• Physical properties of steel
• Sensitivities of high strength tubing
• Tubing inspection
• Tubing handling practices
• Equipment for use with-strength tubing
• Tubing running practices
• API publication list
• Packers and subsurface control equipment
• Production packers
• Subsurface control equipment

Perforating Oil and Gas Well

• Introduction
• Types of perforators
• Evaluation of perforator performance
• Factors affecting gun perforating result
• Perforating in a clean fluid with differential pressure into wellbore
• A comparison between the GEO-VANN system and other perforating methods in wells equipped with packers

Completion and Workover Fluids

• Function-requirements-selection criteria
• Formation damage related to solids
• Oil fluids-practical application
• Conventional water-base mud
• Oil base or invert-emulsion muds
• Foam
• Perforating fluids
• Packer fluids
• Well killing

Through-Tubing Production Logging

• Introduction
• Logging device
• Application of through-tubing production logging
• Field examples of production logging techniques
• Primary cement evaluation

Problem Well Analysis

• Problem wells
• Problem well analysis  checklist

Paraffin and Asphaltene

• Introduction
• Paraffin and asphaltene chemistry
• Deposition mechanism
• Removal of wax depositsPreventing or decreasing wax deposition
• Design of wax control

Squeeze Cementing-Remedial Cementing

• Introduction
• Theoretical considerations
• Practical considerations
• Special squeeze cementing situations
• Planning a squeeze cement job
• Normal operational procedures
• Other operational procedures
• Plug-back operations
• Special cement system

Sand Control

• Introduction
• Reduction of drag force
• Mechanical methods of sand control
• Practical considerations in gravel packing
• Use of screen without gravel
• Resin consolidation methods

Formation Damage

• Introduction
• Basic causes of damage
• Classification of damage mechanism
• Reduced absolute permeability
• Increased fluid viscosity (emulsion)
• Diagnosis of formation damage

surfactants for Well Treatments

• Characteristics of surfactants
• Use and action of surfactants
• Formation damage susceptible to surfactant treatment
• Preventing or removing damage
• Increasing effectiveness of rod pumping
• Prevention of well damage

Acidizing

• Acids used in well stimulation
• Acid additives
• Carbonate acidizing
• Acidizing techniques for carbonate formations
• Sandstone acidizing
• Potential safety hazard in acidizing

Hydraulic Fracturing

• Introduction
• Mechanics of fracturing
• Production increase from fracturing
• Propping the fracture
• Frac fluids
• Frac job design
• Frac job evaluation techniques

Scale Deposition, Removal and Prevention

• Introduction
• Causes of scale deposition
• Prediction and identification of scale
• Scale removal
• Scale prevention

Corrosion Control

• The corrosion process
• Detection and measurement of corrosion
• Corrosion control

INSTRUKTUR

Team Konsultan PT Ganesha Inti Persada

WAKTU PELAKSANAAN

3 Hari (dimulai pukul: 09.00-16.00)

INVESTASI (Tidak termasuk biaya akomodasi & penginapan)

• Rp. 11.000.000, - / peserta (Jakarta)
• Rp. 11.000.000, - / peserta (Bandung)
• Rp. 12.000.000, - / peserta (Yogyakarta)
• Rp. 14.000.000, - / peserta (Bali)
• Rp. 14.750.000, - / peserta (Lombok, Batam, Makasar)
• US$ 4780 / peserta (Malaysia)

FASILITAS

Lunch, sertifikat, Modul, Coffee Break, Training kit diselenggarakan di Hotel berbintang

INFO & PROMO

081296791324 (WA)

021-22830080

CONTACT PERSON

0811-996-1224 (WA)

0812-9679-1224 (WA)

Jadwal Training Online & OfflineTahun 2025:

April

• 9-11 April 2025, Bandung
• 14-16 April 2025, Jakarta
• 23-25 April 2025, Yogyakarta
• 28-30 April 2025, Surabaya

Mei

• 5-7 Mei 2025, Jakarta
• 13-15 Mei 2025, Yogyakarta
• 21-23 Mei 2025, Lombok
• 26-28 Mei 2025, Malang

Juni

• 4-6 Juni 2025, Jakarta
• 11-13 Juni 2025, Yogyakarta
• 18-20 Juni 2025, Bandung
• 24-26 Juni 2025, Bali

Juli

• 2-4 Juli 2025, Bandung
• 9-11 Juli 2025, Jakarta
• 16-18 Juli 2025, Lombok
• 23-25 Juli 2025, Yogyakarta
• 29-31 Juli 2025, Medan

Agustus

• 6-8 Agustus 2025, Bandung
• 13-15 Agustus 2025, Jakarta
• 20-22 Agustus 2025, Malang
• 27-29 Agustus 2025, Bali

September

• 1-3 September 2025, Bandung
• 10-12 September 2025, Surabaya
• 17-19 September 2025, Jakarta
• 22-24 September 2025, Lombok

Oktober

• 1-3 Oktober 2025, Yogyakarta
• 8-10 Oktober 2025, Jakarta
• 15-17 Oktober 2025, Bandung
• 22-24 Oktober 2025, Bali

November

• 3-5 November 2025, Lombok
• 10-12 November 2025, Jakarta
• 17-19 November 2025, Bandung
• 24-26 November 2025, Malang

Desember

• 3-5 Desember 2025, Jakarta
• 10-12 Desember 2025, Bandung
• 17-19 Desember 2025, Surabaya
• 22-24 Desember 2025, Yogyakarta

Klik link form registrasi https://bit.ly/FormRegistrasiPTGIP

Kami menerima request waktu, tempat & fasilitas hubungi kami untuk informasi lebih lanjut.